2016年8月31日星期三

Opcom OP-Com 2012 V Can for OPEL Firmware V1.64 Free Download!

Opcom OP-Com 2012 V Can for OPEL Firmware V1.64 Free Download!

Last week, I found a nice friend shared the latest Op-com FW 1.64 on the forum. I will write the processes here, wish it helpful.

Please attention that I can't take responsibility, all manipulations with the device you are doing at your own risk!

You can download Opcom OP-Com FW 1.64 here:
https://mega.nz/#!CB91DAAL!fCPUZCimVAWcZlhdVpc31wIR0sL837iC4rbGl7WlKyU

1. Please check your chip, it must be a [PIC18F458]. If it is OP-COM chip, it can't be reflashed.


2. 1) Unzip [VAUX-COM_120309a + 131223d_GB + OcFlash China] file to desktop.
   2)Run the program [VAUXCOM.exe] to verify the correct installation of the
drivers.
   3)Click Settings.
   4)Click Test interface.
If the interface appear below, the driver installed properly.


3. You should download the firmware and run the program [OCFlash.exe]


4. 1)Specify the path to the [FW 1.64.hex]
   2)Run the Test interface again and check that the OP-Com updated to version   1.64
   3)You can now use the program [VAUXCOM.exe]


5. Car model until 2015


2016年8月28日星期日

Lexia-3 PP2000 installation error: not possible to start

Lexia-3 PP2000 installation error: not possible to start

Q:when install Lexia-3 on windows XP, it appeared an error as follows, What should I do?

Error message:

AVERTISSMENT

It is not possible to start Peugeot Planet Office for the following reasons:

Peugeot Planet interface is not plugged into the USB port of your PC

Peugeot Planet interface is being utilisation by another application.




















Possible reasons and solutions:

1.Host interface of Peugeot Planet can not be connected to the computer’s USB port;
2.Peugeot Planet 2000 is running on another computer;
3.After closing the other software, then run Peugeot Planet again.

2016年8月26日星期五

VAG CAN PRO SW 5.5.1 installation procedure on XP and win7

VAG CAN PRO SW 5.5.1 installation procedure on XP and win7

VAG CAN PRO support CAN BUS + UDS + K-Line for diagnostics and programming of electronic components used in vehicles Volkswagen, Audi, Seat, Skoda, made from 1990 to 2015.

VAG CAN PRO SW 5.5.1 Operation System:

XP and WIN7, both ok.

We will show the VAG CAN PRO SW 5.5.1 installation video here for user.

How to how to install VAG CAN PRO SW 5.5.1 on win7:



How to install VAG CAN PRO SW 5.5.1 on XP:

2016年8月23日星期二

The experience of use SKP-900 to program new keys for Ford Mustang

The experience of use SKP-900 to program new keys for Ford Mustang

Recently, we used SKP-900 Key Programmer to test remote key for 2014 Ford Mustang. We think it's useful and show the detail procedure here.

Car model: 2014 Ford Mustang

Step follows:

1. First you should connect SKP-900 Key Programmer to the car and turn.
  Choose "SYSTEM SELECTION"  IMMOBILIZER SYSTEM 


2. You should insert the car and turn to "ON", then it will appear a new interface, now please  choose Yesto continue.





3. When it pops out the message (pictures as follow) and you would find that the light on. Please choose YES  to finish this step.



4. You should insert car key again and turning the ignition on, you will find that the light on and off for a while.


5. Please click "No" and go back to the main interface. Finally, try to test whether the remote key can work or not.

2016年8月19日星期五

Super VAG K+CAN odometer correction for VW 2008

Super VAG K+CAN odometer correction for VW 2008

As we all known that Super VAG K+CAN can be used to odometer correction, read Security Access Code, key programmer, airbag reset tool, TV Activation and diagnostic for VW Passat, VW ,VW Bora, VW Polo, VW Golf, Audi A6, Audi A8, Audi A4, Skoda Superb, Skoda Octavia, Skoda Fabia cars. 

Here I will introduce the easiest way to change the VW odometer using it.


How to change the VW obdmeter?

Step1: Please connect Super VAK+CAN, the slot below the dashboard.


Step2: You can see the current mileage is 95000km


Step3: Please click the Odometer Adjust.




Step4: Now you can input the new mileage.



You can check it, look at the odometer, the mileage has changed.


It just cost you a few seconds to finish!

2016年8月16日星期二

VPECKER Easydiag vs. X431 5C Pro vs. Carcare C68 vs. Multidiag Pro+

VPECKER Easydiag vs. X431 5C Pro vs. Carcare C68 vs. Multidiag Pro+

What're the differences among WIFI VPECKER Easydiag, Launch X431 5C PRO scanner, DIY Carecar C68 automotive scanner and Multidiag Pro+ diagnostic system?

Item Name
Launch X431 5C Pro
Carecar C68
Image





Language
Italian, Chinese (Simplified),
English, Chinese
(Traditional), Japanese,
German, Russian, French,
Spanish, Portuguese, Polish
,Turkish, Dutch, Hungarian,
Korean, Czech, Arabic,
Indonesian, Persian, Thai, Vietnamese, Finnish,
Swedish,
Spanish, Arabic,
French, Korean,
Japanese, German, RussianRomanian, Bosnian,
English, Czech, Spanish, French, Russia, Chinese,
Portuguese, Italian, German, Arabic, Japanese, Estonian
English, Spanish, French, Italian, Portuguese, Czech, Dansk, German, Turkish, Greek, Dutch, Hungarian, Norwegian, Polish, Romanian, Russian, Serbian, Swedish, and so on.
Quality
Original
Original
Original
Clone
Update
Update online
Update online
Update online
Update via CD
O/S
PC: Win XP-Win 10 Tablet
Android Tablet
Hand-held, stand-lone
PC: Win XP/Win 7
Bluetooth/WIFI
WIFI
Bluetooth
NO
Bluetooth
User
Technician/DIYer
Technician
DIYer
Technician/DIYer
Vehicle coverage
78 Car brands only
Cars only
60 Car brands Till Year 2013
Cars & trucks till 2014
Function
Basic diagnostic
Special functions, e,g 
Key programming, Oil change, Idle speed learning, Idle speed Adjustment,  Ignition timing adjustment,  Camshaft timing control learning, Maintenance functions, ECU Initial startup, ECU initialization, etc.
Basic diagnostic
(Quick Test, Read ECU Info., Read DTCs, Erase DTCs, Clear learning value, Data Stream, Actuations, Read freeze frame data, Read VIN, etc)
Basic diagnostic
Special functions, e,g , Resets Oil Service Light, Service mileage and service intervals, Replaces and recalibrates brake pads safely etc
Basic diagnostic (Quick Test, Read ECU Info., Read DTCs, Erase DTCs, Clear learning value, Data Stream, Actuations, Read freeze frame data, Read VIN, )

NOTE:
1. Launch X431 scanner and Multidiag Pro+ mainly perform basic diagnostic functions, while VPECKER Easydiag and Carecar C68 are able to carry out special function for some models. 
2. Multidiag Pro+ will do both cars and trucks, others do cars only. 

2016年8月15日星期一

VAG CAN PRO VCP 5.5.1 FAQ

VAG CAN PRO VCP 5.5.1 FAQ

Recently, VAG CAN PRO CAN BUS+UDS+K-line S.W Version 5.5.1 VCP Scanner released. VAG CAN PRO support CAN BUS + UDS + K-Line for diagnostics and programming of electronic components used in vehicles Volkswagen, Audi, Seat, Skoda, made from 1990 to 2015.



About VAG CAN PRO VCP 5.5.1

Q; Is the VAG CAN PRO a full version?

A: yes, it’s VAG CAN full kit.

Q: Does vag can supports coding and programming?

A: definitely yes. The VAG CAN PRO can do offline coding and programming as the original.

Moreover, It doesn’t need engineer codes for coding or programming, while the genuine needs it.

Q: Does it support UDS protocol?

A: yes. It supports CAN BUS, UDS, K-line.

Q: Any difference among VCDS, VCP, ODIS
A: VCDS is good for diagnosis, and simply coding; runs very fast
VCP is best for parametring and quick eeprom read; runs fast
ODIS 3.0.3 is best for flashing; kind of slow when diagnose

2016年8月14日星期日

MB STAR C3 Fault (1.2)-2.503.9551 Solved!

MB STAR C3 Fault (1.2)-2.503.9551 Solved!

Q: I had a diagnostic tool MB STAR C3 but got an error message saying as follows: Fault (1.2)-2.503.9551 error messages, like the picture blew.


A: 1.Error code 95xx: C3 MUX settings is committed
   2.Error code 9551: means no C3 MUX is connected
   3.Error code 9504: means Star C3 is connected and error in MUX
   4.Error code 9500: means C3 is connected but error in COM setting to COM2
   5.Error code 99xx: means C4 MUX setting is committed

There have some solutions you can choose when MB STAR C3 got an error code 9551:

1) Try check your das bin at cal.ini, and make sure command at file already
"PLATFORM=PART_T"if error too.

2) Compare the cable. Change it 1 by 1. First change OBD cable. Next change LAN cable.

3) Use different MUX must make 2 das bin.

4) Uninstall the SD Connect from control panel, restart system, the reinstall SD Connect from backup folder.

5)Send the hard drive back to repair.

2016年8月12日星期五

Using Lexia3 PP2000 xs Evolution to program Peugeot new keys!

Using Lexia3 PP2000 xs Evolution to program Peugeot new keys!

Lexia-3 Lexia3 V48 XS Evolution for Citroen/Peugeot Diagnostic PP2000 V25 updates with free Diagbox V7.76 software now.Lexia-3 Lexia3 V48 xs Evolution can support cars from 1995 to 2013.


Attention: PIN Code is required during key programming procedure. Record your vehicle PIN code first.

How to use Lexia3 PP2000 xs Evolution to program Peugeot new keys?

1. You should install and activate Lexia 3 xs Evolution PP2000 V25 diagnostic software.
2. You should select vehicle model 307 and wait until the well communication built.
3. You should check the entering vehicle information.

 
4. You should select the application as "Peugeot Plant 2000" and confirm it.


5. You should select test by ECU and choose "Built-in systems interface".

6. The system is reading the ECU in progress, follow and accept the windows prompts.
7. You should select "Learning" option under Carry out the tests menu display.


8. You should select "Programming of keys".


9. The system will display key programming procedure when activation process is complete. Confirm to continue.
10. Confirm Unlocking the E.C.U program.
11. Manually enter the "Confidential code" (PIN Code).


12. The system is verifying the PIN code. If the code is correct, the built-in systems interface is ready for programming of keys.
13. Enter the key number to be learnt. The number of keys to be programmed cannot exceed 5.


14. Follow the screen prompt to switch off the ignition
15. Then switch ignition to ON within 15 s.


16. Key programmed, switch off the ignition and take out the key.


17. Switch ignition ON again and insert the next key in the ignition. Repeat the key programming procedure to program another key. When complete programming, the system will display keys that are programmed.


18. Follow the screen instructions. Check the handbrake is on. For an automatic gearbox, check the gear level is in position "P". For a manual gearbox, check that the gear level is in neutral
19. Follow the re-synchronies the HF remote controls procedure to operate until the "End of key programming procedure" notice displays. Exit the program.

2016年8月11日星期四

How to change the language of the Autoboss V30?

How to change the language of the Autoboss V30?

Autoboss V30 original is the recent autoboss scanner. The V30 with bluetooth techniques and live data graphic display, and a 1 year warranty and free update.
Language: English, Spanish, French, Russian, German

How to change the language of the Autoboss V30? Procedure as follows:

Step1: When you get the Autoboss V30, please send supplier the interface series number to open the authorization for you to change language. The series number is like: 1697500025


Step2: You need to wait for 1 or 2 working days for the authorizati

Step3: After the authorization,please open the official website:
http://www.autoboss.net/en/index.asp

Step4: You need to insert the SD card into your computer to log in.

Note:
Log in with the user name and the password.
The user name is the interface series number.
The password is in the setting part of the Autoboss V30. You need to start it to find the password.


Step5: Choose Download when you log in.


Step6: Download the software as the arrow showed on the picture.


Step7: Install the newest software after download. 

Step8: Check the language setting part after the software well installed. Then you can choose the language you want. 

DIGIPROG 3 FAQ Shared

DIGIPROG 3 FAQ Shared

As we all know that the DIGIPROG 3 is the Odometer Master Programmer tool. Recently, many people ask some question about DIGIPROG 3 below:

About vehicle model:

Q: Does Digiprog III change mileage for BMW after 2008year? Does Digiprog3 make key for BMW?
A: Better use Digimaster 3 to program mileage for the high-end BMW. Digiprog3 can't make key for BMW, advice you use AK300 key pro.

Q: Does digiprog3 work with VW golf 6 2009, golf 5 2006 and Peugeot 407 2006?
A: Yes. Digiprog 3 does. You can refer to digiprog3 vehicle list.

Q: I use digiprog3 to work with Opel Astra 2004, and the manual suggests use No.1 cable, this cable is ST01?
A: Yes, No.1 cable is ST01 cable, and the software needs to open off-line programming or online-programming.

About device and accessories:

Q: what is Digiprog III power-on password?
A: Digiprog 3 Power-on password is 1. After enter password "1",
click tick" "not " X", otherwise Digiprog3 will freeze.

Q: What is ST01, ST04 cable used for in the package of Digiprog 3 ?
A: It needs to remove chip when you program mileage for some car models. One end of the ST01 cable and ST04 cable clip the chip, and the other end connect to digiprog3.

Q: What is the difference between tacho pro 2008 and digiprog 3?
A: Tacho pro 2008 and digiprog 3 share the same function. But tacho pro works with the car before 2006 year, digiprog 3 works with the car even up to 2012 year.

Q: Can I use Digiprog3 ST01 cable and ST04 cable to work with Yanhua brand Digiprog 3?
A: Yes, you can, but Yanhua brand Digiprog 3 is better use this following adapter in the package, it works better and more stable.